YELOSUB
02-06-2010, 08:40 PM
***Mods could we sticky this please***
Ok. we forgot to take pics on the first side, and it went way too easy... so we took pics on the other side.
here is the spacer shim and hardware for 1 wheel.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer1.jpg
Before adding 10mm Randode Spacer Shim:
http://i209.photobucket.com/albums/bb107/yelosub/Spacer2.jpg
Break the lug nuts loose, then jack up and support vehicle with jack stands.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer4.jpg
Remove the wheel to expose the brake drum.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer5.jpg
Make sure the parking brake is released and pull off the drum.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer6.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer7.jpg
Locate and remove the four hub bolts with a 14mm socket and ratchet.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer8.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer9.jpg
Locate the ABS sensor wire on the back of the hub. there is a plastic cover over the plug that must be removed to access the button on the bottom to release the plug.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer10.jpg
At this point the hub can be removed.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer11.jpg
Pull the brake backing plate away from the axle flange and slide the spacer shim into place.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer12.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer13.jpg
Line up the shim and put the backing plate back into position.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer14.jpg
Put some red loc-tite on the supplied bolts and bolt the hub back on. Leave the bolts loose until all four have been started. Torque to about 40 foot pounds.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer15.jpg
Plug the ABS sensor wire back onto the hub.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer16.jpg
Reinstall drum.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer17.jpg
Put the wheel back on, torque it down, and lower the car back to the ground.
stand back and admire your new wide stance.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer19.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer20.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer21.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer25.jpg
Spacer shims now in stock for xA, xB, xD, and Yaris...Cube coming soon.
Ok. we forgot to take pics on the first side, and it went way too easy... so we took pics on the other side.
here is the spacer shim and hardware for 1 wheel.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer1.jpg
Before adding 10mm Randode Spacer Shim:
http://i209.photobucket.com/albums/bb107/yelosub/Spacer2.jpg
Break the lug nuts loose, then jack up and support vehicle with jack stands.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer4.jpg
Remove the wheel to expose the brake drum.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer5.jpg
Make sure the parking brake is released and pull off the drum.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer6.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer7.jpg
Locate and remove the four hub bolts with a 14mm socket and ratchet.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer8.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer9.jpg
Locate the ABS sensor wire on the back of the hub. there is a plastic cover over the plug that must be removed to access the button on the bottom to release the plug.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer10.jpg
At this point the hub can be removed.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer11.jpg
Pull the brake backing plate away from the axle flange and slide the spacer shim into place.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer12.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer13.jpg
Line up the shim and put the backing plate back into position.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer14.jpg
Put some red loc-tite on the supplied bolts and bolt the hub back on. Leave the bolts loose until all four have been started. Torque to about 40 foot pounds.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer15.jpg
Plug the ABS sensor wire back onto the hub.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer16.jpg
Reinstall drum.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer17.jpg
Put the wheel back on, torque it down, and lower the car back to the ground.
stand back and admire your new wide stance.
http://i209.photobucket.com/albums/bb107/yelosub/Spacer19.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer20.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer21.jpg
http://i209.photobucket.com/albums/bb107/yelosub/Spacer25.jpg
Spacer shims now in stock for xA, xB, xD, and Yaris...Cube coming soon.