Hi Ted,
Nice job you did! I have been waiting to seee your final results, but in the meanwhile, I need some help/info if you can. I tried to install a Strupp CEL Eliminator, and it requires the dropping of the pipes to install in the O2 Sensor bung. I needed to remove the 2 bolts in the springs at the top of the cat pipe and they DON'T BUDGE !! I used an impact gun that I used to remove the Crank Pulley Bolt, and that couldn't even turn the bolts a smidgen. My bolts are not a bit rusty, and I'm sure rust is not the reason they are'nt moving. Please tell me how you take off those 2 bolts. They're really pissin me off. !!!
Hi Ted,
Nice job you did! I have been waiting to seee your final results, but in the meanwhile, I need some help/info if you can. I tried to install a Strupp CEL Eliminator, and it requires the dropping of the pipes to install in the O2 Sensor bung. I needed to remove the 2 bolts in the springs at the top of the cat pipe and they DON'T BUDGE !! I used an impact gun that I used to remove the Crank Pulley Bolt, and that couldn't even turn the bolts a smidgen. My bolts are not a bit rusty, and I'm sure rust is not the reason they are'nt moving. Please tell me how you take off those 2 bolts. They're really pissin me off. !!!
You couldnt get them off with an impact gun? I hate to ask a stupid question, and I apologize if it offends you, but are you sure you set the gun to loosen the bolts and not tighten them?
I apologize if it offends you, but are you sure you set the gun to loosen the bolts and not tighten them?
LOL, You needn't appologize I had to stop and see if I was going the right way, too ! I was turning the bolt (or should I say Trying to) counter clockwise from the bottom. Since it didn't budge, I tried short bursts of tightening and again loosen, and no dice. The head is showing the impact efforts but it does NOT MOVE I was not sure if there was something else I needed to do befoe those bolts came loose. I'm stumped.
LOL, You needn't appologize I had to stop and see if I was going the right way, too ! I was turning the bolt (or should I say Trying to) counter clockwise from the bottom. Since it didn't budge, I tried short bursts of tightening and again loosen, and no dice. The head is showing the impact efforts but it does NOT MOVE I was not sure if there was something else I needed to do befoe those bolts came loose. I'm stumped.
They could be frozen... try using some pb blaster, or liquid wrench...
They say if you cant take an elephant down with a 9mm, try a bigger gun...
Just keep in mind that if you break the head off, your pretty much F*cked...
[QUOTE=TheLittleDeviant;2996]They could be frozen... try using some pb blaster,QUOTE]
Whoa Baby !! Neva heard o sump'n la datt, but went to buy a can to try anywayz. Squirted dem bolts once and 30 minutes later squirted em 'gin. If I dint' see it fer mahself ahd neva believe it! Them shiny babies turned on the second impact gun "pack" and spun clear off. Yesterday, I hit em and hit em with 5 second bursts and they wouldn't budge fer nuttin! I went and bought a second can (NAPA had em on sale fer 1.49 per 7oz. can - Checkers wanted 7 bucks) Ah's gonna brush mah teeth comb mah hair and use a shot fer mah un'er ahms wi dat dem dere magic 'Catalyst'. Heck da old lady wants to smak some on mah pecker, since it's so good. Best thing since soft toilet paper we ever got! Thank ya podnah, really do preciate yo kindly advice.
Ted, YOUDAMANNNNN !!!!!
bob
Mahalo Nui Loa
Last edited by bobolinko; 11-10-2009 at 02:37 AM.
Reason: spelling woz not so good
!!! 
I had to stop and see if I was going the right way, too ! I was turning the bolt (or should I say Trying to) counter clockwise from the bottom. Since it didn't budge, I tried short bursts of tightening and again loosen, and no dice. The head is showing the impact efforts but it does NOT MOVE I was not sure if there was something else I needed to do befoe those bolts came loose. I'm stumped.
Hybrid Mode
